KeepAlive Aerators, Oxygen Systems and Livewells

will keep your fish alive and healthy




KeepAlive Aerators, Bait Tanks, Green Lights, Bait & Bilge Pumps, & Oxygen Systems




KeepAlive Aerators and Bait Tanks keep tournament fish and bait alive and healthy




Tel. 727-841-0407

P.O. Box 1952, Tarpon Springs, FL 34688

Fax 727-815-8049



Portable Units

Re-circulating Kits

Thru-Hull Units

Bait Tanks

 Low Pressure Air Diffuser

Oxygen Systems

Green Lights

Bilge Pumps

Guide To Aeration


Places To Purchase

Technical Manual






Download Printable Version



This simplified guide is intended to teach the fundamentals of the proper aeration and oxygen techniques in keeping live bait, and "catch & release" fish, alive and healthy in live wells.


The advantages as well as disadvantages of many types of aeration will be discussed.


There are many misconceived ideas about aeration.

Two common fallacies are:

1.      Large live wells are required to sustain a large quantity of fish.

2.    Large live well pumps are needed to move large quantities of water through the live well to keep live bait and fish alive.

To understand what is really needed for proper aeration, it is best to take a parallel look at ourselves and fish.


1.      If we were enclosed in a large airtight room we would be able to breathe for many hours before we would consume all the oxygen.

2.    If we were in an airtight closet, the oxygen would be consumed a lot quicker.

3.    If we were swimming underwater without a snorkel, the oxygen in our lungs would be consumed very quickly.

4.    In all cases, without additional oxygen we would eventually expire!

However, we could stay alive indefinitely, if we could use a breathing tube or snorkel that was in contact with outside fresh air or oxygen. It would not matter about the size of the container or the quality or air that surrounded us.


1.    If we enclosed a fish in a sealed, 1,000 gallon tank, it would survive for a long time before consuming all the oxygen.

2.    If we enclosed the same fish in a sealed 10 gallon tank, the oxygen would be consumed more quickly.

3.    If we removed the same fish from the tank and placed it on a table, the fish could live for an extremely short time.

4.    In all cases, without additional oxygen the fish would eventually die.

However, our fish could stay alive indefinitely if we could put oxygenated water through its gills and keep it wet.  It would not matter about the size of the tank.




1.    It is more difficult to breathe through a straw than through a large snorkel.

2.    A small or ineffective aerator cannot provide as much oxygen in the water as a larger or more effective one.

3.    If an aerator can provide enough oxygen in the water for the fish to breathe, it doesn't matter how much water surrounds the fish! The only reason that water must be changed occasionally in live wells is to remove ammonia. The smaller the container of water, the more frequent the changing.


The major considerations in aeration are:

1.    The gentleness and direction of water flow.

2.    The size and amount of the air bubbles.

3.    The temperature of the water


FISH THAT SWIM IN SCHOOLS:  Delicate bait such as shad, green-backs and croakers will not survive a day of fishing unless the water flow in the well is soft and gentle. Turbulent water will damage the bait and force them to work against the current. Ideal water flow within the well should be approximately 1 to 2 MPH, and in a circular motion. This will allow fish to school and provide a smooth flow of water over and through their gills. If the water flow is excessive, bait tire quickly and will not be lively. Keep water flow as low as possible, with fish swimming in a stationary position within the tank. Do this with a few pieces of bait to see how they behave.

SHRIMP AND FISH THAT DO NOT SCHOOL:  Species that do not school, do not need a circular or oval container. Keep water flow to a minimum for fish such as bass, redfish, crappie, bream, and walleye.

For shrimp, provide material in the well so they can cling and not be swirling about the well and become damaged. Leave a dip net in the well, or tie a stone in a piece of cloth such as burlap, or a piece of fiberglass screening.


Take a look at the air bubbles produced by an aquarium aerator. Watch how quickly the bubbles rise to the surface. They provide little aeration, but are aesthetically pleasing to watch. Bubbles must remain contacting the water, if they are to do the job properly. A good rule of thumb is: The smaller the bubble, the longer it will remain suspended in water to dissolve.


The warmer the water, the less oxygen it will hold. Fish will deplete the oxygen quicker as the water warms, and poor aerators will maintain less fish.  Colder water will hold more oxygen. Water frozen in a plastic bottle will lower temperatures and keep the chlorine out of the tank.  

Use an aquarium thermometer to compare temperatures. Keep temperatures within 8º F between water in the well, and water outside the boat.

 CAUTION: Placing fish in different temperatures quickly, will shock and kill them. It is best to place fish in the same water and temperatures where they were caught.

A Lesson in Air Bubbles

1.    The smaller the air bubble, the more slowly it will rise, giving it more time to dissolve in the water.

2.    Due to the higher density of salt water, air bubbles are usually smaller in salt water than in fresh water.

3.    A large 20mm bubble has a volume of 4.19 cm3, and a surface area of 12.6 cm2.

4.    You could make 260 small 3mm bubbles from the large bubble. They would have a total surface area of 83.6 cm2. This is 6.6 times the surface of the 20mm bubble.

5. small bubbles, can theoretically aerate 6.6 times as much water with the same amount of air.


Knowing the importance of air bubble size, the effectiveness of different aerator systems becomes readily apparent!



Livewells come in many shapes and sizes. Oval or round tanks provide the best circulation. However, rectangular or square wells are satisfactory if there is a directional discharge into the well. The directional discharge will induce the more desirable circular motion.

Species that do not school, do not need a circular or oval container. Keep water flow to a minimum for fish such as bass, redfish, crappie, bream and walleye. They do not need a water flow for survival.

For shrimp, provide material in the well so they can cling and not be swirling about the well and become damaged. Leave a dip net in the well or tie a stone in a piece of cloth such as burlap.


1: WHITE. Most purchased bait tanks are white or translucent. A white tank is desirable to reflect heat. However, this creates the following problems:

A.   Brightness inside the tank causes stress.

B.   Any shadows on the outside wall of the tank will be seen on the inside of the wall. Fish will react to the shadow. It represents either a predator fish or a diving bird, and they will slam into the other side of tank and create injuries to themselves.

2: WHITE EXTERIOR WITH BLUE INTERIOR. This is the preferred tank. The white exterior reflect the heat, while the blue interior will cause a blue haze inside the tank and fish stress will be considerably reduced.


When using aerators, there is very little advantage in using an insulated tank. All aerators take in outside air. If it is a cold day, the temperature entering the bait tank will blend with the water, and the water will eventually reach the cooler outside temperatures. If it is a warm day, the temperature entering the bait tank will blend with the water, and the water will eventually reach the warmer outside temperatures.


An insulated tank has a tremendous advantage when pure oxygen systems are used. Pure oxygen systems are self contained and so temperatures within the tank are maintained. O2 exiting an oxygen cylinder will be slightly cooler, but negligible, since only a small amount of oxygen is needed to maintain fish.


Oxygen will maintain higher quantities of fish, but extra care must be taken when using pure oxygen. To understand the fundamentals or air versus oxygen, each should be individually discussed.


A human breathes in oxygen and gives off carbon dioxide (CO2). The CO2 is then dissipated directly into the atmosphere.

For fish, water is an additional barrier that must be overcome. A fish breathes in oxygen from the water and gives off CO2. The CO2 is absorbed into the surrounding water. The CO2 is then dissipated into the atmosphere through the process of aeration.

An air bubble as it passes through water has the ability to put oxygen into the water and also absorb CO2 as it passes slowly to the surface. The bubble then pops at the surface and the CO2 is dissipated into the atmosphere. The smaller the bubble, the longer it remains in the water to exchange oxygen and CO2.


An oxygen bubble will insert a higher percentage of oxygen into water than a normal air bubble. This allows for higher quantities of fish in a given size of container, or it will make bait fish lively. However, an oxygen bubble does not have the ability to absorb CO2. As the fish eliminates CO2 in its body, there will be a build-up of CO2 in the livewell water. When the percentage of CO2 equals that of the fish, the fish will be unable to expel the CO2 and absorb the enriched oxygenated water. If a closed livewell does not have the ability to aerate and remove the CO2, the fish will suffocate. In a rolling boat, water at the surface of your livewell that is in contact with air, will produce aeration and may be sufficient to remove CO2 without introducing other forms of aeration. This is called de-gassing.



Oxygen systems are predominately used by large aquariums such as Georgia Aquarium,  Monterey Bay Aquarium, Ripley’s Aquariums, and Sea World.  They are now available at affordable prices to all anglers.


Theory suggests that large percentages of oxygen in water will turn your bait into star performers and attract more fish. Predators are attracted to faster moving bait. Many members of the Southern Kingfish Association have been using pure oxygen systems for years.

To increase the oxygen percentages higher than what would be normally found in the water entering your livewell, the intake pumps to the well should be turned off. Otherwise, oxygen enriched water produced by your oxygen system will be dumped overboard and defeat the purpose of producing livelier bait. 


Aeration systems should be turned off when enriching water with higher than ambient levels of oxygen. When aerators are on, they will try to keep oxygen levels at normal conditions. You won't produce livelier bait, but they will remain healthy. Remember that oxygen cannot absorb and dissipate CO2, so high levels of CO2 in the water will eventually kill your bait. Watch your bait occasionally to see if they start to stress. If stress occurs, immediately start your aeration system or change the water in the livewell. This condition is extremely rare in a rolling boat, since degassing will occur naturally with water moving in contact with air.

One recommendation when fishing tournaments, is to keep aeration and oxygen systems both operating until 20 minutes prior to reaching your fishing area. Then turn off the aeration or fill pumps to allow oxygen levels to build in the water, and allow time for the bait to increase physical activity. CO2 levels will be low in the livewell, so more time can be spent fishing rather than observing your bait. When changing areas, replace the water or start the aerator.



Pure oxygen systems will keep your fish livelier and healthier than aerator systems. In addition, they are self contained and no external power is required!


Fishing oxygen infusion systems are designed for use in a marine environment. They are the latest technology for anglers to maintain bait and catch. Oxygen systems have been used by large commercial fish farms and aquariums for many years. KeepAlive® provides oxygen systems to large aquariums and this technique is now available for all anglers.


OXYGEN REGULATORS, DIFFUSERS, AND CYLINDERS regulators use a CG540 valve to connect the regulator to the oxygen cylinder. The cylinder can be filled at most welding shops.  They are never used for medical purposes.

Marine grade fishing regulators are exposed to the marine elements and are made of brass with nickel plating. Anodized aluminum regulators with internal brass, designed with non-rusting components and designed to prevent intrusion of spray and humidity can be used and are a good alternative choice for many anglers. They can be either a needle valve or rotating barrel with preset openings. The rotating barrel is the preferred choice. Only a small amount of oxygen is needed to maintain fish so the first settings are very small.

Never lubricate or spray your regulator. This will contaminate the regulator and may render it inoperative.


The diffuser is the most important item of your equipment. Inexpensive air stones precious oxygen. Bubbles are large and do not maintain contact with the water long enough, and are of little use to good oxygenation. Diffusers are made of ceramic with tightly formed pores. They require 25 to 35 lbs of pressure to force the oxygen through ceramic pores, resulting in micro-fine bubbles. The bubbles are so small that they stay suspended in the water and the water absorbs the oxygen. Ceramic diffusers will give many years of service. If the pores clog at the surface due to impurities in the water, a light sanding on the ceramic surface will generally solve the problem.


Oxygen cylinders usually come in three or four sizes, made of aluminum and powder coated to prevent rust spots on your boat, and use the CG540 welding valve. Use the largest cylinder that will fit on your boat comfortably. The cost of refilling a cylinder is generally the same, so there are substantial savings if you are fishing frequently.

Some welding shops have programs where you can purchase your cylinder and trade it for another filled cylinder immediately. The only disadvantage to this type of program is that the cylinders are steel and care must be taken to prevent rust spots on your boat.

Care must be taken to secure the high pressure cylinder securely to your boat. Do not secure your cylinder in a closed compartment.


Oxygen trans-fills can be used to fill your smaller boat cylinders from larger welding oxygen cylinders to reduce oxygen costs. Care must be taken to SLOWLY crack open cylinder valves to allow oxygen to transfer SLOWLY. TRANSFERRING OXYGEN TOO QUICKLY MAY OVERSTRESS YOUR CYLINDERS AND CAUSE HEAT BUILDUP ON YOUR CYLINDER. To ensure good safety practices and prevent errors, use trans-fills that have slow filling orifices.


Warning: Not for medical use.


Pure oxygen is not an explosive. It is an oxidizer and allows things to burn more quickly. Never smoke or have an open flame in the proximity of pure oxygen.

BUBBLE AERATORS WITH AIR STONES operated bubble aerators are an inexpensive way to keep bait alive in small containers. They are an entry point for anglers looking to purchase an inexpensive aerator to maintain small amounts of bait for short periods of time. They provide gentle aeration, but are inefficient because of non-uniformed bubble pattern and coarse bubble size. Cost is the primary factor in producing air stones that are packaged with your aerator. They sustain less bait per unit of air than a high quality, low pressure ceramic diffuser, producing smaller bubbles.


Most bubble aerators use AA, C, or D cell batteries, and operational costs can become expensive. a bubble aerator is the only option available, invest in a low pressure ceramic air diffuser.  


KeepAlive® manufactures a low pressure ceramic diffuser with micro bubbles that dramatically improves the efficiency of a bubble aerator. They are expensive in comparison to air stones because of the intensive  manufacturing process, but if a bubble aerator is your only option in maintaining fish, then purchase a high quality bubble aerator and couple it with the KeepAlive® KA975 Low Pressure Ceramic Diffuser. It improves most bubble aerators by 600%. This is the equivalent of purchasing 6 bubble aerators. If properly maintained, your low pressure ceramic diffuser will provide for many years of efficient service.  



When maintaining catch and bait with pumps, the most important requirement is the reliability of your pump. They are all similar in appearance, and it is difficult to decide which pump will provide long lasting reliable service by looking at them.


Many pump manufacturers just add intake bases to their bilge pumps and call them livewell pumps. Bilge pumps do not require the endurance to operate for long periods of time, and many brands of bilge pumps cannot provide the stamina of continuous operation as livewell pumps.


The following aeration systems use pumps to maintain fish in livewells. Choose your pump wisely!


Spray bar aerators add oxygen to the water by jetting small streams of water into the surface. Some air is absorbed into the spray as it passes from the spray bar to the water surface, and when the spray strikes the water surface, air bubbles are injected into the water. For the most part, these bubbles are rather large.


Jets of water from spray bars are generally harsh to delicate bait. Their protective coating and scales are easily removed, and their survival is drastically reduced.


Spray bars are an inefficient aeration system, and should be used only on the hardiest bait.


This is the much copied, old aeration technology. They can be purchased as a floating aerator or a bottom aerator with suction cups.

The fast-moving water at the output of the pump creates a vacuum, which suck air into the pump output. This system typically provides better aeration than spray bar aerators, but the efficiency is still low.

Some models damage bait due to the high speed of water from the pump output.


Thru-hull pumps provide a constant flow of new water into the livewell and eliminate the problems of heat and ammonia build-up. As long as clean water is available, more bait can be placed in a given amount of water than with any of the previously discussed aeration systems. However, when entering water that is less than ideal for delicate bait, care must be taken to secure the intake water. By utilizing a combination of the thru-hull pump with other aeration methods, bait can remain healthy and lively for longer periods of time.


KeepAlive® Infusors are revolutionary Oxygen Infusion Systems, GUARANTEED TO OUTPERFORM ALL OTHERS! They might look like the competition, but their superior is completely different. Air is infused with the water at the pump impeller. The micro-fine bubbles produced, are sent gently out of the pump and into the livewell, containing life giving oxygen.


KeepAlive® Infusors are specifically designed for delicate shad, KA500Fgreenbacks and white bait.  The millions of micro-fine bubbles are so small that they remain suspended in the water longer thus providing more oxygen for your bait and catch. Our smallest model will aerate from a 5-gallon bucket up to a 55- gallon drum or livewell, gently and efficiently. KeepAlive® Infusors will virtually disappear in a mass of micro-fine bubbles when used in salt water.


The water speed is controlled by its Air Control Center to allow fish to school in a stationary position.


KeepAlive®  ALWAYS uses the best long lasting pumps available in the industry. We periodically torture test different brands of pumps endurance to ensure a quality product. They are all similar in appearance, and it is impossible to decide which pump will provide long lasting reliable service by looking at them. That is why we test them.


KeepAlive® Infusors are available as a bottom infusor with suction cups, a floating infusor, or permanent recirculating livewell and thru-hull infusors. Conversion kits are available to convert your Rule bilge pump or Rule livewell pump to the exciting KeepAlive technology!

KeepAlive® Infusors are an investment that will save you time and money by keeping your bait healthy and lively longer than any other comparable aeration system. . . . . GUARANTEED!

Don't let your fishing trip end before its time, just because your bait did!

Make KeepAlive® a part of your fishing gear!

KeepAlive® . . . the newest technology in aeration and oxygen systems!


KeepAlive Aerators and Livewells
will keep your fish alive and healthy!