MARINE COMPRESSED GAS OXYGEN REGULATOR OPERATING INSTRUCTIONS AND SAFETY GUIDE

BEFORE OPERATING YOUR OXYGEN REGULATOR,
PLEASE READ THESE INSTRUCTIONS

MAINTENANCE AND CARE

Wipe down with a clean, soft cloth. If contaminated, the regulator should be taken out of service immediately.

If your FISH-FLO2 Oxygen Regulator is accidentally immersed in salt water, remove the red dust cover from the safety relief valve,  flush well with fresh water, and let dry before using again.

CONNECTION GUIDELINES

Never stand in front of a cylinder outlet or regulator when operating the cylinder valve. Remove the two protective covers from the 540 Valve Nipple and the Hose Barb before attempting to connect to a cylinder. DO NOT REMOVE THE 5/8" DIAMETER RED DUST COVER FROM THE SIDE OF THE REGULATOR NEXT TO THE HOSE BARB. IT IS THERE TO HELP PREVENT CONTAMINATION. REFER TO THE  SAFETY TIPS AND WARNINGS BEFORE PROCEEDING FURTHER. Be sure to properly inspect both the cylinder and regulator for any signs of grease and oil. If grease or oil is suspected or found, do not use this device.

TRANS-FLO2 FLEXIBLE TRANSFILLING ASSEMBLY

Directions For Use

1. Read all warnings before proceeding.
2. Remove the red protective caps from the ends of the Transfill Adapter and fully close the Relief Valve.
3. Connect the Transfill Adapter supply fitting to the high pressure "Supply Tank" using the Handwheel. This is the housing that contains the gauge and relief valve.
4. Connect the other end of the Transfill adapter to the tank to be filled, "Receiving Tank", using the other Handwheel. Do not support any weight with the hose.
5. Fully open the cylinder valve on the "Receiving Tank" SLOWLY!

6. Slightly open the cylinder valve on the "Supply Tank" SLOWLY!
7. Wait until the sound of contents being transferred has stopped.
8. Fully close the the cylinder valve on the "Supply Tank" SLOWLY!
9. Fully close the cylinder valve on the "Receiving Tank" SLOWLY!
10. Open the Relief Valve on the Tranfill Adapter SLOWLY!
11. After the pressure has been relieved, remove the Transfill Adapter and replace the red protective caps.

Specifications

Warning
Do Not change gas service.
Do not use hose to support equipment.
Always open cylinder valves very slowly.
Do not exceed the working pressure of this assembly.

Hose and connections should be regularly checked for
wear, abrasion, cutting, contamination and movement.

Cleanliness must be maintained through out the complete system. Use no oil.
Never use thread sealants that are not approved for oxygen service.

Failure to follow these instructions may result in serious personal injury and property damage.

SAFETY TIPS AND WARNINGS

2. Never use oxygen around or near an open flame.

3. Never smoke in an area where oxygen is in use.

4. Never use oxygen near boat bilges or where gasoline fumes may be present.

5. Never use industrial oxygen from a cylinder without reducing the pressure through a regulator intended for that specific gas.

6. Never force connections that do not fit properly.

8. Refill cylinders slowly to prevent excessive heat build-up and possible damage to cylinders.

9. Keep out of reach of children.

10. Always be sure that all fittings and threads are matched and properly for the gas intended.

11. Never use oxygen as a pressure source to clear an obstructed line or to operate pneumatic tools.

12. Always keep the oxygen cylinder secured.

2. Never use oxygen around or near an open flame.

3. Never smoke in an area where oxygen is in use,

4. Never use industrial oxygen from a cylinder without reducing the pressure through a regulator intended for that specific gas.

5. Never force connections that do not fit properly.

7. Keep out of reach of children.

8. Always be sure that all fittings and threads are matched and properly for the gas intended.

9. Never use oxygen as a pressure source to clear an obstructed line or to operate pneumatic tools.

10. Always keep the oxygen cylinder secured.

CONNECTING A CGA 540 NUT AND NIPPLE INLET

1. Check to be sure that the valve on the cylinder is off.
2. In a clockwise direction, thread the regulator inlet nut onto the cylinder valve.
3. Tighten the inlet nut with the hand-wheel attached to the regulator.

OPENING/CLOSING THE CYLINDER VALVE

1. Before turning on the oxygen cylinder valve, check to be sure that the regulator is in the "0" position.
2. Stand behind the cylinder so that the cylinder is between you and the regulator. Remember: Never stand in front of a cylinder outlet or regulator when opening the cylinder valve.
3. Begin turning the cylinder valve counter-clockwise VERY SLOWLY to open the valve.
4. If you suspect a leak, turn the cylinder valve off and relieve the pressure by turning the flow selector knob clockwise and wait for the oxygen flow to stop. Then, turn the regulator off by turning the selector knob to the "0" position. Remove the regulator from the cylinder. Call your authorized FISH-FLO2 Dealer.

WARRANTY AND REPAIR SERVICE

FISH-FLO2  warrants that the manufactured components of the product furnished hereunder shall be free from defects in material and workmanship for a period of six (6) months from the date of purchase. This warranty does not cover failure resulting from immersion, contamination, accidental damage, misuse or operation not in accordance with the instructions provided. To keep this warranty in effect, all repairs must be performed by FISH-FLO2.  This warranty is null and void if unauthorized repairs are attempted or performed. After receipt of product, FISH-FLO2 will evaluate and determine whether or not the repair is covered by warranty. For repair service of any kind, you must first call for a return materials authorization (RMA). This RMA # must appear on the outside of the box. Any shipment received without an RMA on the outside will be refused. You should enclose a description. of the problem Repairs are subject to a flat labor rate per regulator. Returns are subject to a 20% restocking fee. Returns are not accepted after 30 days from date of purchase or if product has been used.

LIMITED-LIFETIME REPLACEMENT WARRANTY

Because or the harsh unforeseen conditions that the FISH-FLO2 Oxygen Regulator may be subjected to, the regulator is also covered by a limited-lifetime warranty. If a problem is found at any time and caused by any reason including, but not limited to, accidental damage and contamination, return the regulator to FISH-FLO2 and receive a new replacement FISH-FLO2 Oxygen Regulator for $75.00 plus shipping. To qualify, all regulator parts must be included with the regulator and the the serial number must be legible.

You must first call FISH-FLO2 at 1-888-567-7733 and give the customer service representative a valid credit card number and obtain a Replacement Regulator Authorization Number (RRA). This RRA  number must appear on the outside of the box containing the returned regulator. Any shipments received without an RRA number will be refused. A new replacement FISH-FLO2 Oxygen Regulator will be shipped out the next business day.

UNDER NO CIRCUMSTANCES SHOULD ANY REPAIRS, OR REPLACEMENT OF ANY PARTS BE PERFORMED BY ANYONE EXCEPT FISH-FLO2.